Primarily designed for Noisy Environs
normal loud ringing is drowned or is
difficult to hear. The unit gives excellent
"bounce around" from the strobe
light. Easy to install - mount on wall,
plug into power outlet and then plug into
Telephone Line.
During incoming ring, the unit produces
a sound and also flashes a strobe light.
The sound type is adjustable across 32
settings using internal adjustments.
Suitable for direct Telephone Lines and
Analog Phone ports of PABX Systems.

• Fly Lead with BT Plug Supplied as Standard
• 22Vdc - 240Vac Power Adaptor Included
• Wall Mountable
• Amber or (optional Clear, Blue, Green, Red available)
• 2 Part Unit
• Strobe Output
• Sound Output - 1 of 32 Tones
• Volume Control
• Very High Light Output
• Telephone Cord - 2 metres
• 22Vdc plug pack

• Telephone line powered (no mains voltage required).
• Greatly reduced installation costs.
• Penetrating output(105dBA typical).
• Volume control.
• Available for hard wiring (screw or I.D.C.) or with 3 metre line cord.
• IP66 Rated.
• REN of 1.5.
• Maintenance free operation

• Approved for New Zealand and Australia

• Adjustable Warble Generator Built-in
• Full Range of Tone Adjustment
• Volume Control
• Telecom Line Input Trigger
• Low Voltage AC/DC Input
• Audio Input
• Clean Relay Contact Input
• Interface to other External Devices

• Frequency: 80Hz to 20kHz
• Sensitivity: 89dB +/-2dB at 1.0W, 0.5m (600Hz)
• Audio output: 3.5Wrms continuous in to 8 ohms
• Volume Control
• Power adapter: DC 22~24Vdc, 350mA (Included)

Features:
* Much louder than normal telephone
* Audible and Visual indication of incoming call
* Suitable for use with all telephones and most Key Systems and PABXs
* Easy DIY self installation
* Tone Adjustment: High/Medium /Low (pitch)
* Rate Adjustment: Fast/Medium/Slow (warble)
* Volume Adjustment: High/Low/Off
* 3 Modes of operation: Audio and Visual/Audio only /Visual only
* AC or battery powered (note: Visual indication is only available when AC powered)
* Can also be activated by 24Vac/dc signals
* Wall mountable
* Supplied with all installation accessories including: Plug Pack, modular adaptor plug, 10m extension cord, wall mounting screws and 17cm wall mounting cord.

Specifications:
* Output level: more than 100dB SPL
* AC ring Detection: 40 to 120Vac RMS at 14 to 55Hz (centre pins)
* DC/AC Detection: 24 to 50 Vac/dc at 3 to 15mA (selected by internal strapping)
* REN: 1

• Telephone Ringing Voltage Detection with Relay and FET programmable outputs.
• Message Waiting Detection - Voltage Detection on PABX systems only
• Relay and FET Reverse Role
• Power Supply Excluded
• 12 to 48Vdc Operation and Switching
• Easy Wiring

Specifications:

• 12 to 48Vdc Operation
• 12 to 48Vdc <1A Resistive Load on either output
• Use to Drive your own External Devices
• Slave Relays available for larger loads.
• Built-in 10sec Time Delay if required.
• Built-in PABX Message Waiting Detect if required.
• Power FET Output for Sounder or Light/Strobe Options
• Relay Output for Light or Strobe Options
• Can have Strobe Continuous Power Drive State during ringing cycles and sounder Ringing with the Ring Cadence at the same time.
• Relay can follow ringing cadence or HOLD between ring cycles
• Power FET can follow ringing cadence or HOLD between ring cycles
• (must have Relay HOLD as well to work otherwise follows Relay)
• With the PABX Message Waiting Facility it can be used in Call Centres and Hotels etc. for an easy solution to advise supervisor and others that calls are being missed. Adjustable 65Vdc to 100Vdc simultaneous to Ringing Detection. Therefore, for practical reasons can only be used for one or the other.
• POTS or PABX Hold between ring cycle period selectable.
• Relay can be disconnected via a LINK so as only FET can switch giving totally silent switching for Radio Station Hotlines etc. ie. no relay clicking on Microphone in Studio.